N1mm logger default messages install#
N1mm logger default messages driver#
N1mm logger default messages skin#
N1mm logger default messages software#
N1mm logger default messages Pc#

VFO changes take forever to do (either click n drag or wheel on Hercules are slooooow.mouse wheel is quck though) but VFO changes on RX1 are instantaneous and fast (normal) I've unplugged the Hercules and power cycled everything.and the 2nd slider (right hand one) still isn't doing anything.the Centre and Zoom are only having an effect on RX1Р”Р„lso just noticed that RX2 has gone into 'sledge/limp' mode i.e. changing to some of the other skins causes the odd crash, but not on all of them.

N1mm logger default messages skin#

The 2 sliders are there (2nd one none functioning) but not on my preferred SKIN i.e. I did a snapshot but Photobucket is having a meltdown on me.gonna have to find an alternative image sharer. I don't have the 2 'slider' bars like you e to think of it i haven't seen the old slider bar for a while it wasn't a problem as i adjusted the zoom via my Hercules MP3LE midi controller.but this is only adjusting (zooming) on RX1 only. The N1MM screens switch to the appropriate band now (many thanks), although i'm certain i could open 2 'spectrum' windows (was always same band) before.no biggie if that has gone. So is this a fault, bug or error on PSDR or the N1MM Logger+ Spectrum Monitor ?Р”Р„lso FWIW i can open another window (N1MM spectrum) but it always shows the same as window 1.any way i can have 2 windows (spectrum) open but showing the display's from both RX1 AND RX2 ? Several checks/experiments later it didn't matter which way round i altered first RX2 first the RX1 it always defaulted to the 'last' panafall (on PSDR) that i was hovering over (mouse FOCUS) that determined which panafall was displayed on the N1MM spectrum.this wasn't a problem per se but the frequency on the top bar never changed ( always read whatever RX1 was, never RX2 even if the spectrum was showing RX2). PG 8-3 ICOM 7610 BASIC MANUAL.I'm not sure if this is a fault/bug but earlier this evening i was listening to 80M (RX1) and 40M (RX2) and had the N1MM Logger+ Spectrum Monitor open on another monitor.this was fine until i came to adjust the vfo on RX1.RX1 adjusted ok.but.the N1MM Logger+ Spectrum Monitor whilst showing the frequency at the top of the window/bar was showing the panafall from RX2 !!. MINE IS SET TO 20MS BECAUSE I USE AN AMERITRON AL-811. IMPORTANT: IF YOU DRIVE A LINEAR AMPLIFIER WITH YOUR ICOM 7610, INCREASE YOUR TX DELAY TO AT LEAST 10MS. Sherwood Engineering HF Test Results РІР‚вЂњ Icom 7610

N1mm logger default messages driver#

Icom 7610 USB Driver Download Page from Icom Whatever the reason for visiting my website, I appreciate the comments. Maybe youРІР‚в„ўre waiting for one or researching. I hope you find this informative and useful even if you donРІР‚в„ўt own a Icom 7610. I know it can be frustrating at times to get it all working smoothly, IРІР‚в„ўve been there before and I still make mistakes. Thank you for coming by and I hope this helps. Rob Sherwood, NC0B, has done a preliminary review and points out a couple of helpful tips. I think one should be removed, because it is incorrect and I donРІР‚в„ўt believe the reviewer owns the IC-7610.

N1mm logger default messages install#

Install Fldigi and when you open N1MM Logger Plus go to Config>Configure Ports>Digital Modes and tell N1MM Logger the Fldigi path. If you want, you can download and install Fldigi for CW decode. N1MM Logger Plus configuration is included and it works perfectly for me. When it gets to the MMTTY configuration, pay close attention to the settings and especially EXTFSK64. I have a short video on this.Р”В®verything you need, including the Icom 7610 internal settings, are in the video. The Icom 7610 uses two virtual COM ports and we use one USB 2.0 cable. If you donРІР‚в„ўt, both are pretty straight forward installs. I am presuming readers are familiar with N1MM and MMTTY and have them installed. It is only available on a few select radios and the IC-7300/7610 are included. The Spectrum Display is relatively new and a lot of fun to use. N1MM Logger+ also has the Icom 7610 listed in rigs.

N1mm logger default messages Pc#

With N1MM Logger+ we also get a nice Spectrum Display (waterfall) on the PC monitor.

N1mm logger default messages software#

N1MM Logger, MMTTY, EXTFSK are the software programs for RTTY (FSK) being used with the Icom 7610. I will get a good quality dynamic mic to try out.Р’В The Icom 7610 LCD touch screen is outstanding.Р’В Noise blanker, noise Reduction and notch filtering are superb, the best I have seen.Р”Р„s a prerequisite, always install the Icom 7610 USB driver before connecting the USB cable.

A few have said it sounds like my Icom 7300! I am using the same mics I used with the 7300, the Yamaha CM500 and the BM800. The TX audio quality is similar to the IC-7300.

IРІР‚в„ўve pulled out some pretty weak signals using the filtering and IРІР‚в„ўm very impressed with the RX. Operating digital modes, like FT8, is so quiet, I hardly know IРІР‚в„ўm transmitting. I have had the Icom 7610 for a little over a week now and WOW! What a quiet and smooth transceiver.